Independent editorial research • US models • How our links work

COMPARISON / 1kWh CLASS

BLUETTI Elite 100 V2 vs Anker SOLIX C1000 Gen 2: Which Is Better for You?

A compact station meets the higher-output alternative. Same 1,024Wh, but two different ideas about what matters most.

WattPick Lab editorial desk · Updated · US models

Affiliate disclosure: WattPick Lab may earn a commission from qualifying purchases through affiliate links, at no additional cost to you. Editorial conclusions are independent of commissions. How our links work.

BLUETTI

Elite 100 V2

Compact footprint, with a high solar ceiling

US 120V model
Nominal energy
1,024 Wh
Rated AC output
1,800 W
Approximate weight
25.3 lb

Manufacturer specifications · LiFePO₄ battery

ANKER

SOLIX C1000 Gen 2

Higher output and faster charging, smaller solar ceiling

US 120V model
Nominal energy
1,024 Wh
Rated AC output
2,000 W
Approximate weight
24.9 lb

Manufacturer specifications · LiFePO₄ battery

QUICK VERDICT

A near tie on size — a real split on solar and output.

Both store 1,024Wh with LFP chemistry and roughly 4,000 cycles to 80%. Both weigh within half a pound of each other, which makes this the closest pair in the 1kWh class on portability.

CHOOSE ONE

Choose BLUETTI Elite 100 V2 if… or Anker SOLIX C1000 Gen 2 if…

BLUETTI Elite 100 V2

  • Solar headroom matters more to you than raw output
  • You want the more compact of the two
  • You are staying in the 1 kWh class

Anker SOLIX C1000 Gen 2

  • You want more rated AC output
  • You expect to add capacity later
  • You want the larger built-in battery

These two disagree about what matters most in a 1 kWh station — solar headroom in one case, raw output in the other. Affiliate links · price and bundle may change.

Side-by-side specifications

Published manufacturer specifications
SpecificationBLUETTI Elite 100 V2Anker SOLIX C1000 Gen 2
Nominal capacity1,024Wh1,024Wh
Battery chemistryLiFePO₄LiFePO₄
Rated AC output1,800W2,000W
Surge / high-load modeUp to 3,600W surge; 2,700W Power LiftingUp to 3,000W peak
Maximum AC chargingUp to 1,200WUp to 1,600W UltraFast
Advertised full AC chargeAbout 70 minutesAbout 49 minutes
Maximum solar inputUp to 1,000WUp to 600W
UPS switching≤10ms10ms
Cycle life4,000+ cycles to 80%4,000 cycles to 80%+
Output portsPowers up to 11 devices10 ports
USB-COne 140W; one 100WUp to 140W
Battery expansionNot a modular systemNot supported
WeightAbout 25.3lbAbout 24.9lb
Dimensions12.6 × 8.5 × 9.8 in15.12 × 8.19 × 9.61 in

Specifications are drawn from the manufacturer documentation listed under Sources. Verify the exact regional model and current manual before purchase.

AC output: Anker has 200W more

Anker is rated at 2,000W continuous AC output against BLUETTI’s 1,800W. That 200W matters if the simultaneous load approaches the smaller ceiling. For small electronics it may change little. Peak and boost modes are not substitutes for the continuous rating.

Charging: Anker is much faster on mains, BLUETTI has far more solar

The main solar difference is 1,000W maximum input on Elite 100 V2 against 600W on C1000 Gen 2. Match a real compatible array and expected daily harvest; a small panel does not use either ceiling.

Anker advertises about 49 minutes to full using its specified UltraFast mode; BLUETTI advertises 80% in 45 minutes. Those are different charge windows, not like-for-like test results. Compare the exact mode, input source and conditions.

Portability: the closest category here

Anker lists 24.9 lb; BLUETTI about 25.3 lb. Anker is slightly lighter. BLUETTI’s advantage is the compact footprint, not the lightest weight. Check vehicle storage and usable space as well as the small weight difference.

Ports: a modest BLUETTI advantage

Compare the actual ports your devices use, particularly USB-C power and simultaneous limits. A higher port count alone is not a reason to choose one station. Use the published port table rather than treating device-count marketing as delivered power.

UPS and home backup

Both describe switching in the approximately 10ms class. That is not zero interruption or guaranteed compatibility with every device. Test your intended backup load and low-load settings before depending on automatic operation.

The limitation they share

Both are fixed-capacity 1,024Wh stations without supported battery expansion in these models. If the daily budget is likely to exceed 1kWh between recharges, compare a larger or documented expandable platform. Output and faster charging do not add stored energy.

FINAL VERDICT

Pick the priority, not the brand.

Choose C1000 Gen 2 for the higher continuous output and mains-focused recharge routine. Choose Elite 100 V2 when the compact footprint and higher compatible solar-input ceiling matter more. Both remain fixed-capacity 1,024Wh stations; the small weight gap is not the main buying difference.

Still deciding?

Neither of these supports battery expansion. If you expect to need more than 1kWh later, start with the pairing that does.

Other 1kWh pairings

Want one model in full?

Stepping up a class

Sources & editorial method

Sources & methodology

Research checked September 24, 2026. This comparison covers the US versions of both models. We use official documentation for specifications and label every estimate as such. Charging and solar recharge times are manufacturer claims under stated ideal conditions and are not guaranteed outdoor performance.

  1. BLUETTI Elite 100 V2 US product page ↗ — capacity, output, ports, charging, solar input and weight.

Live offers and bundle contents should be checked at the retailer.